Box of Drywall Nails
Drywall can make a great surface for your home, but if you don't know how to work with it, it can be just as frustrating as most materials. This is particularly the case if you've got some annoying drywall nails on your hands. As drywall gets older and the wood changes, nails can sometimes change position, leading them to make bumps in the wall or even crack them open. If you want to fix those annoying drywall nails, this article will help you get started.
First, consult this article on "How Stuff Works" in order to check out the equipment you might be needing. A nail set will come in handy, as well as some basic tools like a hammer and sandpaper.
Next, you'll want to drive the popped nails back to where they were. If one is sticking out too far, simply remove it so that you can drive it back in again. You can use your nail set at this point. Remember that you're using your nail set, so the nail might go deeper than you originally thought it would be.
One of the reasons this nail might have popped out in the first place is that the change in the wood put pressure on it, squeezing it out of place. You can relieve some of this pressure by driving in a new nail about two inches above the old one onto the same stud in the drywall.
At this point, your drywall won't look very good - in fact, you will probably have two holes with nails in them. That's why it's important to be ready to cover up the drywall again. Clean out the area and then fill in the holes with a spackling compound. You can use your putty knife for this. Make sure the area is even with the rest of the drywall. After this spackle has dried, sand down the area and then apply primer and paint to match the rest of the drywall. Make sure that you touch up this area as needed, but allow it time to dry.
After these repairs, your drywall should look good as new, and hopefully with the repairs you've made, you won't have to worry about that drywall nail popping out again for a while. Doing these quick repairs should help you better understand how drywall works, as well.
Photo Credits: Bistrosavage
Originally posted 2010-01-21 03:53:36.
This post involves:
... and focuses on:
Posted by Fix Handyman on January 4, 2012 in
Drywall, Handyman, How to Fix, Walls
Loose or Broken Tile?
Whether your kitchen floor is new or old, there's nothing that disturbs the balance of a room quite like a broken tile. After all, tiles were installed with a pattern in mind: break one link in the chain and the whole thing falls apart. That's why it's important to know how to fix a broken tile - like learning how to change a tire, sometime it pays to know how before you have to do it.
First, we can assume that the conjoining material between each tile is already hard, which means that you'll have to do a little work that might include dust and debris. Make sure to wear protective eye goggles - you might even want to cover your mouth to prevent inhaling too much dust into your lungs.
Next, you'll have to destroy and remove any leftover spots from the previous tile. Most likely your tile is still in place, unless the whole tile itself came out already. In order to remove tile chips, you're going to want to follow a precise pattern: break the tile in the center using a hammer and nailset, and then cut the tile into an X pattern using a glass cutter. Then you can use the hammer to chip away the rest of the tile - beginning in the center - and pry up the pieces using a metal tool.
Once the area is cleared of the main tile bits, it's time for you to dry it out - suck out the remaining debris with a vacuum cleaner. It might not hurt to sand down any protruding areas that might get in the way for the new tile, so be sure to vacuum after you've done the sanding, as well.
Now that you have a clear area where your tile used to be, it's time to replace the tile. First you're going to want to fill the area with latex primer and allow it to dry - you should probably make sure to protect this area so that no one steps in it, particularly small children if you have them. After the primer has dried, you can apply tile adhesive, making sure to move it left and right to make sure it settles in properly. It's important to keep the tile level, so use a mallet to make sure that it gets in far enough. Any extra tile adhesive that comes out of the sides can be scooped up with a stick or screwdriver.
Give the tile some time to dry and you should be all finished. You've covered up the spot in your kitchen that detracted from all the rest. Now if you could just get a new set of cupboards.
Photo Credits: wakingphotolife
Originally posted 2009-08-04 13:55:27.
This post involves:
... and focuses on:
Posted by Fix Handyman on December 14, 2011 in
Floors, Handyman, How to Fix, kitchen
Stumble
Reddit
Digg
Del.icio.us
