Shower Drain
As drains age, they begin leaking. Often, the piles loosen, the putty dries up or the tape begins to lose its effectiveness, causing water to trickle down the drain. If you have a sink drain that leaks, you can mend it by following the steps outlined here. And by attending to it yourself, you’ll be saving by not calling in a plumber!
First, close the tap before starting work. Next, remove all the fittings of the drain by unscrewing them, using a screwdriver. Next, take off the tailpiece. Ask a friend or family member to hold the drain pipe from over the sink while you loosen it with pliers.
If your drain has a plastic retainer, unscrew it before the drain pipe comes loose. Now that you have disassembled everything, clean it thoroughly. Check that you have cleaned the previous plumber’s putty from the fittings of the drain. If something is left over, it will weaken the bond when you put it back altogether and begin to leak once more.
Now, coat the part under the rim of the drain pipe with 0.5” thickness of plumbers’ putty to prevent future leakages. Remove any excess putty from the pipe or you will find it very difficult to clean it once it dries. Now, replace the drain pipe into the drain and screw all the fittings to the pipe below the sink. This simple operation will repair your leaky drain.
However, if you have a leaky shower drain, water may collect around the edges and make its way to the ceiling below it. To repair this, cut a panel in your ceiling downstairs. However, if you live in a rented accommodation, speak to your landlord and have him repair it or get his approval before doing it yourself.
Now, place some cloth on the floor just where you want to get down to work. Wear a pair of goggles. Then, make a cut of about 1.5 feet square into your ceiling that’s just below your shower drain, using a saw. Remove the locking unit using pliers and then the gasket.
Now, in the bathroom, loosen and take off the packing nut from the leaky drain. Remove the drain collar and clean the area around it with a putty knife, and clean the shower drain entirely.
Next, take about an inch of plumber’s putty and coat the base of the drain collar with it. Replace the drain collar using a very firm hand or some of the putty you just applied will come off. This is normal, so don’t panic. Once this is done, screw the locking nut tightly again and then take off any extra putty from around here and replace the packaging nut where it belongs. Use silicone caulk to keep this packing nut firmly in place.
To test if the leak is plugged, open the tap and let a little cold water trickle out. Now, if there is no leakage, you will need to repair the drywall. If a leak persists, call a plumber.
Photo Credits: lavenderstreak
Originally posted 2010-04-20 17:59:08.
This post involves:
... and focuses on:
Posted by Fix Handyman on August 28, 2010 in
Drains, Handyman, How to Fix, Plumber, Shower
Bubblebath anyone?
For many people, the bathtub isn't just a way to get clean, it's an oasis away from the stress and worries that come with daily life. Whether you indulge in a luxurious bubble bath every night or just enjoy a good soak now and then, it's important to keep your bathtub clean, neat, and most importantly, functioning. So how can you fix some of the most common bathtub problems? I thought you'd never ask. Here are the answers to some common bathtub questions.
Fixing a Bathtub Faucet Clog
One of the most frequent problems you'll see with a bathtub is that the faucet gets clogged. This isn't like unclogging a toilet - you actually might have to do some plumbing. But before you conjure up images of tool belts and blue jeans, remember that plumbing isn't complicated every time.
In each bathtub faucet there is a screen that helps make sure that any loose debris doesn't get plopped into your bubble bath, allowing you to enjoy clean, pristine water. The problem with this screen is that it can sometimes collect too much debris and actually clog your water from coming through with a full flow.
If you can, remove the faucet head in order to get to the screen. Take out the screen and wash it with warm or hot water, and use that time to clean out the inside of the bathtub faucet. If you have further problems but don't want to explore before you do further damage, call a plumber.
Fixing a Drain Clog
The next and perhaps more unpleasant problem with bathtubs is that sometimes the drains clog. You don't want to bathe today in yesterday's bathwater, so it's important that you get this drain cleared as soon as possible.
Though you'll want to clean the part of the drain you can see first, this rarely solves the problem itself. You'll want to plunge the drain like you would plunge a toilet, trying to remove as much of the blockage as possible. Fill a little water in your tub before you plunge.
If that doesn't work, you'll have to use a plumbing snake to get the clog out. Be patient with a plumbing snake, as oftentimes you'll have to go very deep before you can reach a clog. Once you do, voila! Good as new.
These are two of the most common problems that occur with bathtubs because they get in the way of the flow of our daily lives. The bathtub drain, for example, also effects the way we take showers. Even if you're initially frustrated, stick with your plumbing efforts as long as you're not doing any damage. You'll probably learn something.
Photo Credits: Darrius Thompson
Originally posted 2009-08-18 03:03:45.
This post involves:
... and focuses on:
Posted by Fix Handyman on June 23, 2010 in
Bathroom, Bathtub, Handyman, How to Fix
How to Unclog a Clogged Toilet in Three Steps
Ugh - there goes the toilet again. Today's toilets are more eco-friendly because they use less water per flush, but this also means they pack less of a wallop than the less-efficient toilets of yesteryear. Which means you'd better be ready to unclog a toilet, but don't worry: it's not as hard as you thought. Here are three steps for doing just that.
- Step 1. First, make a few preparations.
If you don't know what's clogging the toilet, try to ask anyone else who lives with you if they might know. This, of course, will depend on your individual situation and whether or not you already know what's causing the clog. Second, as you're preparing to unclog the toilet, try to spread a few towels around the area - it's likely that you'll splash some toilet water around. Make sure you wash these towels after you're done.
- Step 2. Use a plunger.
This is the basic tool you'll use when working with toilets, and for most clogs, this might actually be your only step. If you've never used a plunger before, don't fret; it's actually pretty simple.
First, you'll want to make sure that there's enough water in your toilet bowl to cover the head of the plunger. Make sure that you don't actually flush the clogged toilet again - instead, you'll want to simply add some water from an external source like a faucet. This will help make the plunging go more smoothly and make sure you get adequate pressure to unclog your clog.
- Step 3. If the plunger fails, try a toilet auger.
This isn't your first option; you'll want to use the auger for the especially stubborn clogs that the plunger simply isn't able to handle.
A toilet auger is much like a plumber's snake, but it is often treated with a plastic coating to help protect the inner workings of your toilet. Using the auger, you can actually "reach in" and manually dislodge a clog by either grabbing it and pulling it back up, or by pushing it through down to your drainage line.
Working with a clogged toilet is one of the easiest things to fix around the home - as long as you know what you're doing. Keep a couple of these tools (a plunger and an auger) handy around the house - you just need one of each. This way you can avoid unnecessary trips to the hardware store or calls to the plumber.
Photo Credits: apartment therapy
Originally posted 2009-07-30 03:30:52.
This post involves:
... and focuses on:
Posted by Fix Handyman on June 3, 2010 in
How to Fix, Plumber, toilet
Bathtub or toilet clogged? Grab a plunger!
Being able to plunge away a bathtub or toilet problem with a plunger is one of the basic home improvement skills everybody should know. It might not always be the most pleasant task, but it's simple, easy to learn, and it often gets the job done. The better you understand how to fix a clogged drain with a plunger, the less you'll need to work. Here's how to most effectively fix your drain using a plunger.
First, what kind of plunger do you have? Most of us imagine the stereotypical bell-shaped plunger, but you might have seen other options at the local hardware store. Use the "stereotypical" one; this bell-shaped plunger should be able to fold back to become flatter when you need to unclog either a sink or a bathtub. There are less-traditional plungers that aren't able to change their size for the type of drain you'll be unclogging; try to avoid these.
Next, it's important to understand that plungers work better if they're encased in water. If your toilet is clogged and there's hardly any water in the bowl, fill a container with water and use it to fill up the toilet bowl about halfway up. Once you have enough water over the drain to essentially cover the end of the plunger, push the plunger over the drain and form a seal around it. Now, pump the plunger over the drain keeping the seal tight, usually using much of your force to push in the plunger. You should notice that the clog appears to be loosening; however, you might not be able to tell until you flush the toilet again.
You can probably try another round of plunging if this doesn't work. If your plunging still seems fruitless, you'll have to move to the next step on the plumbing ladder: using a snake to break up the clog. If you use a snake and continue to have trouble with a clogged drain that seems totally blocked, it will probably be time to call the plumber.
Most of your clogs, however, should break up once you use a plunger. At the very least, you'll be able to loosen up a clog enough to get your toilet working again. When it comes to other clogged drains - such as the bathroom sink or the bathtub drain - you can fold back the plunger and use a similar method of plunging, making sure that there's some water present above the drain.
Photo Credits: julia fredenburg
Originally posted 2009-08-03 13:55:51.
This post involves:
... and focuses on:
Posted by Fix Handyman on May 12, 2010 in
Bathroom, Bathtub, How to Fix, Plumber, toilet
Stumble
Reddit
Digg
Del.icio.us
